Diecast Display Wall Cube — Stackable 1:64 Car Display Case with Clear Acrylic Window

A modular display cube for 1:64 diecast cars. Each cube has a clear 1 mm acrylic front window and click-lock splines, so you can stack cubes side by side and on top of each other into a display wall that grows with your collection.

Pick the cube that suits the car: three shelves for mainline cars, two taller shelves for premium cars and vans, or one deep bay for a monster truck. All of them share the same 108 mm face and the same joints, so you can mix them in one wall.

• 3-Shelf (mainline): 3 shelves, one car per shelf. Each shelf takes a car up to about 76 mm long, 25 mm wide and 25 mm tall
• 2-Shelf (premium / vans): 2 shelves for taller cars, up to about 78 mm long, 27 mm wide and 36 mm tall
• Deep (monster truck): 1 deep bay for a truck up to about 90 x 65 x 65 mm. It stands further forward and lines up flush at the back with the standard cubes
• 4-Pack: four 3-Shelf cubes
• Window: clear 1 mm acrylic, 4 x 4 in (101.6 x 101.6 mm). Gravity holds it in a groove; to open, push it up about 3 mm, tip the bottom edge out and lift it away
• Click-lock splines: a small printed spline slides in from the back across each seam and clicks into place. Pull it out from the back to take a cube out of the wall. Nothing shows on the front
• Size: 108 x 110.6 mm face; 48.3 mm deep (3-Shelf and 2-Shelf), 85.3 mm deep (Deep)
• 3D printed in PLA (matte or basic finish, 14 colours), made to order in Melbourne, Australia

In the box: per cube, the cube, one clear acrylic window (4 x 4 in, 1 mm, with a protective film on both sides) and 2 click-lock splines. Cars and miniatures are not included. All pictures are photos of printed cubes in Matte Black.

Fits: most 1:64 diecast cars, e.g. Hot Wheels® and Matchbox® mainline cars, and many 1:64 monster trucks in the Deep cube. Check your car against the sizes above if it is unusually long or tall. It also suits small display pieces such as a painted 32 mm-scale miniature. Not affiliated with, or endorsed by, Mattel or any diecast brand; brand names are used only to describe fit.

Need a custom size (e.g. Premium, Car Culture, 1:43)? Contact us: [email protected]

Care: peel the film off both sides of the window before use. Clean the window with a soft cloth and water, or a little mild soap. Do not use alcohol, glass cleaner or solvents on it, because they can craze acrylic. PLA softens above about 55 °C, so keep cubes out of hot cars and direct sun.

SAFETY & USE: this is a display case for collectors, not a toy. The splines are small parts: keep them away from children under 3. The cubes are freestanding and stack on a shelf or desk; they are not designed to be screwed to a wall, and no fixings are included. Damage caused by dropping a stack or by using the cubes in a way they aren't designed for isn't a fault in the product. This doesn't affect your rights under the Australian Consumer Law.

What material is the Diecast Display Wall Cube — Stackable 1:64 Car Display Case with Clear Acrylic Window printed in?
Printed in plant-based PLA — made from renewable plant sugars (corn & sugarcane), not petroleum — with a lower carbon footprint than traditional plastics. Every order is printed to order in Melbourne, so there's no mass-production waste and nothing sitting in a warehouse.

What finish should I expect?
It's 3D printed to order, so fine layer lines and small support marks are normal. Need a smoother finish? Email [email protected] before ordering and we'll tell you what we can do.

How long does shipping take?
Australia: $10 standard / $15 express, free standard shipping over $100 · New Zealand: $15 · United States: $20 · Other countries: $25. Every item is printed to order and ships in 3–5 business days from Melbourne. Finish: every piece is 3D printed to order, so fine layer lines and small support marks are normal. Need a smoother finish? Ask us before ordering. Faulty, not as described or our mistake? We'll fix it, reprint or refund, and cover the return. To report a problem, email [email protected] with your order number and photos; we may ask for the item back. Changed your mind? Standard (non-personalised) items can be returned unused within 30 days of delivery, with return shipping at your cost; personalised or custom-made items can't be returned for change of mind. This doesn't affect your rights under the Australian Consumer Law. Full terms: formada3d.com/legal-en#returns

Where is it made?
Designed and 3D printed to order in our Melbourne, Australia workshop.

What's your returns policy?
Faulty, not as described or our mistake: we fix it, reprint or refund, and cover the return. To report a problem, email [email protected] with your order number and photos; we may ask for the item back. Change of mind: standard (non-personalised) items can be returned unused within 30 days, with return shipping at your cost. This doesn't affect your rights under the Australian Consumer Law.