42 mm Grid Organiser Set — Baseplate, Stacking Bins & Tool Block

A desk and workshop organiser on the open 42 mm grid. The baseplate takes any 42 mm grid bin, and our bins drop into any 42 mm grid baseplate, so it grows with whatever you already have. Buy the starter set, or just the pieces you need.

Starter set: one 3x3 baseplate (126 x 126 mm), a 1x1 bin, a 1x2 bin, a 2x2 bin and a 2x1 tool block. The bins hold screws, bits, paints, SD cards, pens and the small stuff that drifts across a bench. The tool block has six pockets for 1/4-inch hex bits, three 9.5 mm pockets and two 13.5 mm pockets for drivers and handles.

• 3x3 baseplate: 126 x 126 x 5.55 mm, 42 x 42 mm cells, takes any 42 mm grid bin
• Bin 1x1: 41.5 x 41.5 x 26.6 mm (3 height units)
• Bin 1x2: 41.5 x 83.5 x 47.6 mm (6 units)
• Bin 2x2: 83.5 x 83.5 x 47.6 mm (6 units)
• Tool block 2x1: 83.5 x 41.5 x 21 mm, six 1/4-inch hex-bit pockets, three 9.5 mm and two 13.5 mm pockets
• Bins stack: the foot of each bin seats in the lip of the one below, chamfer on chamfer, so stacks centre themselves
• Follows the open 42 mm grid specification (42 x 42 mm cells, 41.5 mm bin footprint, 7 mm height units). Prints from other makers can vary a little
• No magnets, no hardware: nothing to fit. This version has no magnet holes
• 3D printed in PLA (matte or basic finish, 14 colours), made to order in Melbourne, Australia

In the box: the piece or set you choose, in one colour. Bits, drivers and other contents shown are not included. Photos are of a printed set in Matte Black.

Need PETG for a hot workshop, other bin sizes, or a bulk order for a shop fit-out? The same set is in our business parts catalogue, quoted per job.

Care: PLA softens above about 55 °C, so keep it out of hot cars, window sills in full sun and off heaters. Wipe clean with a damp cloth. For storage of dry goods only; not for food.

Will these bins fit my existing 42 mm grid baseplate?
Yes. The feet follow the open 42 mm grid specification (42 x 42 mm cells, 41.5 mm bin footprint, 7 mm height units), so our bins drop into any 42 mm grid baseplate and our 3x3 baseplate takes any 42 mm grid bin. Prints from other makers can vary a little.

Do the bins stack, and are there magnets?
They stack: the foot of each bin seats in the lip of the bin below, chamfer on chamfer, so a stack centres itself. There are no magnets and no magnet holes in this version, and nothing else to fit.

Can I get other sizes, PETG, or a bulk order?
The shop sells the starter set and the five standard pieces in PLA. Other bin sizes and heights, PETG for a hot workshop, and bulk orders are quoted per job through our business parts catalogue at business.formada3d.com/parts/.

What material is the 42 mm Grid Organiser Set — Baseplate, Stacking Bins & Tool Block printed in?
Printed in plant-based PLA — made from renewable plant sugars (corn & sugarcane), not petroleum — with a lower carbon footprint than traditional plastics. Every order is printed to order in Melbourne, so there's no mass-production waste and nothing sitting in a warehouse.

How long does shipping take?
Australia: $10 standard / $15 express, free standard shipping over $100 · New Zealand: $15 · United States: $20 · Other countries: $25. Every item is printed to order and ships in 3–5 business days from Melbourne. Returns per Australian Consumer Law — if it arrives faulty or not as described, we make it right.

Where is it made?
Designed and 3D printed to order in our Melbourne, Australia workshop.

What's your returns policy?
Returns are handled per Australian Consumer Law — if it arrives faulty or not as described, we make it right.